If you require further assistance please contact us by sending email to export cisco. You dont have to erase the old IOS, it can stay as long as you have enough space. It shouldn't ask you to erase anything. But either way, you should say no. Nothing will be erased. Unless the new IOS patch does not support some old features of the older patch, then those simply will disappear.
Given your current version, you should be all OK. It's not free. You'll need a valid contract number from cisco to download IOS. You download it from Cisco. To upgrade the IOS, you'll need to first download it from cisco. No only choose yes if you dont have enough memory to install the new ios. If you have the enough dram and flash memory to support it then YES. YES it look like you have the space for upgrading - here.
The release notes would usually tell you if you need to install a intermediate IOS before the final one, however as this rtr isn't supported anymore, not sure this information is available, If the recommended flash memory is the same , I would go for a straight upgrade and see if it works, obviously backup you rtr beforehand and if possible keep both old and new IOS on the flash so you can boot to the old one if the upgrade fails.
Buy or Renew. Find A Community. Cisco Community. Search instead for. Did you mean:. All Community This category This board. Cisco Router. I have this problem too. All forum topics Previous Topic Next Topic. Martin L. VIP Advocate. In response to Martin L. VIP Advisor. In response to moman The configuration on that subinterface is:!
Our monitoring system also shows some traffic that use more than the 13 Mbps. Thanks in advance. Labels: Labels: Routing Protocols. Tags: QoS I have this problem too. All forum topics Previous Topic Next Topic. Joseph W. Hall of Fame Expert. Disclaimer The Author of this posting offers the information contained within this posting without consideration and with the reader's understanding that there's no implied or expressed suitability or fitness for any purpose.
Liability Disclaimer In no event shall Author be liable for any damages whatsoever including, without limitation, damages for loss of use, data or profit arising out of the use or inability to use the posting's information even if Author has been advised of the possibility of such damage. Posting Notice in the output policy 30 second offered rate bps and that is more that the 13 Mbps configured and more use than we expected in the Internet link. In response to Joseph W. In response to pablo. Posting Are you sure you monitoring is looking at the correct variable?
Thanks in advance for your help. Table 2 describes the slot number and name for the USB slots. To upgrade the system image on your router review the following sections:. System images contain the Cisco IOS software. Your router was shipped with an image installed. At some point, you may want to load a different image onto the router or the access point.
For example, you may want to upgrade your IOS software to the latest release, or you may want to use the same Cisco IOS release for all the routers in a network. Each system image contains different sets of Cisco IOS features, therefore select an appropriate system image to suit your network requirements. You must have an account at Cisco.
If you do not have an account or have forgotten your username or password, click Cancel at the login dialog box and follow the instructions that appear. To download a system image you must have an account at Cisco. If you do not have an account or have forgotten your username or password, click Cancel at the login dialog box, and follow the instructions that appear. This section provides information about upgrading the Cisco IOS image on the router. To avoid unexpected downtime in the event you encounter serious problems using a new system image or startup configuration, we recommend that you save backup copies of your current startup configuration file and Cisco IOS software system image file on a server.
To save backup copies of the startup configuration file and the system image file, complete the following steps. Copies the startup configuration file to a server. Displays the layout and contents of a flash memory file system. The following example shows the startup configuration being copied to a TFTP server:. The following example uses the dir flash0: command in privileged EXEC mode to learn the name of the system image file and the copy flash0: tftp: command in privileged EXEC mode to copy the system image to a TFTP server.
The router uses the default username and password. This section describes how to check whether your router has enough DRAM for upgrading to the new system image. Choose the Cisco IOS release and system image to which you want to upgrade. Write down the minimum memory requirements for the image, as displayed in the File Download Information table. See the hardware installation guide for your router.
Step 2 Write down the minimum memory requirements for the image, as displayed in the File Download Information table. Step 3 Use the show version command to display the router processor and memory. This section describes how to check whether your router has enough flash memory to upgrade to the new system image and, if necessary, how to properly delete files in flash memory to make room for the new system image.
Use the secondary CF for overflow files, if required. Table 3 lists CF slot number, name, and size. Slot0 4. Slot0 is the default CF slot. CF in Slot0 stores system image, configuration, and data files.
Table 4 lists the USB slot number, name, and size. From the File Download Information table, write down the minimum flash requirements for the image. From the displayed output of the dir flash0 : command, compare the number of bytes available to the minimum flash requirements for the new system image. From the displayed output of the dir flash0: command, compare the number of bytes total to the size of the system image to which you want to upgrade.
Optional Repeat Step 7 for each file that you identified in Step 6. Repeat Step 9 for each file that you identified in Step 6. From the displayed output of the dir flash0: command, compare the number of bytes available to the size of the system image to which you want to upgrade. Step 1 enable. Use this command to enter privileged EXEC mode.
Enter your password if prompted. For example:. Step 2 dir flash0 :. Use this command to display the layout and contents of flash memory:. Step 3 From the displayed output of the dir flash0 : command, compare the number of bytes available to the minimum flash requirements for the new system image.
Step 4 From the displayed output of the dir flash0: command, compare the number of bytes total to the size of the system image to which you want to upgrade. Use this command to display a list of all files and directories in flash memory:.
If you cannot delete any files, you must upgrade your compact flash memory card. Note Do not delete the system image that the router already uses. If you are not sure which files can be safely deleted, either consult your network administrator or upgrade your compact flash memory card to a size that can accommodate both the existing files and the new system image. Optional Copy a file to a server before deleting the file from flash memory.
Step 8 Optional Repeat Step 7 for each file that you identified in Step 6. Use this command to delete a file in flash memory:. Step 10 Repeat Step 9 for each file that you identified in Step 6. Step 11 dir flash0 :. Step 12 From the displayed output of the dir flash0: command, compare the number of bytes available to the size of the system image to which you want to upgrade.
This section describes how to copy the system image into the compact flash memory card for your router. Choose one of the following methods:. This is the recommended and most common method of upgrading the system image.
0コメント